How To Install Cabinet Microwave

1. 1

   Use an appropriate microwave. A recirculating or forepart-venting microwave tin be installed below a counter without any farther effort. Other types may require more advanced ventilation installation. Exist aware of the requirements of your model before y'all brainstorm installation.

   • Other types of microwave may be more than suited for an over the range installation, crave a new ventilation hood, or even necessitate a total new ventilation arrangement.

2. two

   Locate the wall studs. Follow these methods for finding and mark these vertical wall supports. Your microwave volition need to be fastened to at to the lowest degree one of them.^[one]

   • If y'all take one, utilise an electronic or magnetic stud finder to search for nails.
   • Alternately, tap lightly on the wall with a hammer. When y'all hear a solid "thunk" instead of a hollow sound, you've likely found a wall stud.
   • If you lot're not certain whether you've constitute a stud, drill a test hole and use a bent wire or coat hanger to search for solid objects in your wall.^[ii]
   • Once you've located the middle of one wall stud, its closest neighbors are normally located either sixteen inches or 24 inches to each side.^[three]
   • Apply a small nail to probe the wall stud(s) and make up one's mind the width.^[4]
   • Draw a vertical line downwards the heart of the wall studs once y'all've found them.

   Advert

3. 3

   Place the mounting plate. This flat metal plate should be level and the summit tabs should butt against the base of operations of the cabinet or chiffonier frame.^[five]

   • If your microwave came with a wall template, record that instead every bit a drilling guide before you lot attach the plate.
   • Apply a level to ensure your microwave isn't installed at a camber.
   • Remove any decorative trimming from the chiffonier preventing yous from placing the mounting plate correctly.
   • If the forepart of the cabinet has an overhang, identify the mounting plate below the back of the chiffonier past an equal amount. Otherwise the overhang will block admission to the microwave. For a microwave that requires base of operations-of-cabinet attachments, you lot may need to saw off the overhang instead.

4. 4

   Locate and drill the correct attachment holes. ^[6] Follow these steps to determine which size holes to drill and where.

   • The bottom edge of the plate should take an area covered in holes. Use a mark to draw circles in at least ii holes. At to the lowest degree one should be completely over a wall stud to back up the microwave's weight.
   • Locate the two or more holes along the upper border of the microwave. Fill in these with a marker as well.
   • Remove the mounting plate. Employ the circles you drew every bit a guide, not the mounting plate.
   • Drill a 3/xvi" (5mm) hole through whatsoever circle located on a wall stud.^[7]
   • Drill a 3/viii" (10mm) hole through whatsoever other circle.^[8]
   • If your microwave came with a top template, tape information technology to the base of the cabinet above and drill iii/8"(10mm) holes through attachment points where directed to fasten the microwave to the cabinet base of operations.

5. 5

   Drill a 1.five" – 2" (four-5cm) hole for the power cord. If your microwave came with a base of cabinet template, record this where the microwave top will exist located and drill where instructed for the power cord. Otherwise, select a spot easily accessible past the power cord and out of the way of normal cabinet part.

   • If there are no electrical outlets within reach of the cord, you will need to install a new electrical outlet. Do non apply an extension cord.

6. 6

   Secure the mounting plate. Have an assistant hold the mounting plate securely in the correct position equally you spike it to the wall.

   • Use lag screws (lag bolts) in the iii/xvi"(5mm) holes. These will bear near of the microwave's weight, which is why they are used over the wall studs.
   • Use toggle screws (toggle bolts) in the 3/8"(10mm) holes. The "wings" of the toggle screw become through the hole and pull against the wall equally the screw is tightened. Pull the mounting plate toward you while tightening toggle screws.^[9]

7. vii

   Mount the microwave. With an banana's assist, hang the microwave onto the support tabs on the mounting plate's base.^[10]

   • Snake the power cable through the hole drilled for this purpose before attaching the microwave.
   • Fasten the microwave to the base of the chiffonier above using screws where directed on the peak template. Tighten until the top of the microwave and the base of operations of the chiffonier are flush.

   Advertising

1. 1

   Check every surface of your microwave for vents. You don't need a special model of microwave to identify it on a shelf, but you lot exercise demand to know where the vents are for proper installation

   • Countertop models usually have vents on the sides and top of the microwave, but back panel vents are common as well.^[11]
   • If you are having trouble finding the vents, place the microwave on a tabular array, plug it in, and heat food or liquid within. Place your paw nigh each side of the microwave to experience for blowing air.

2. two

   Remove the turntable and any other loose objects from inside the microwave. This is especially wise if your chiffonier is high up, since the tabular array can easily fall out of the microwave during lifting.

3. 3

   Place the microwave in a recessed chiffonier or on a shelf. Make certain the vents are not affluent against whatsoever surfaces or objects. There should be at least an inch of infinite next to each vent.^[12]

4. 4

   Replace the turntable and plug the microwave in. If the cord volition not reach or is in an inconvenient location, temporarily remove the microwave and drill a pocket-size pigsty in the cabinet or shelf to snake the cord through.

5. 5

   Clean the microwave vents every three months or so. Because the chiffonier does non allow as much air movement around the vents, dust volition gradually build up and increase the risk of burn down.^[13]

   • Wipe the vents with a damp fabric while the microwave is turned off.

   Advertisement

Add together New Question

• Question

  How practise yous install a microwave in a higher place the stove?

  

  Gevorg Grigorian is an Appliance Repair Specialist and the Owner of One thousand and R Appliance Repair in Los Angeles, California. With over 12 years of experience, Gevorg specializes in residential and commercial appliance repairs likewise as heating, ventilation, and air workout (HVAC) services. Gevorg holds a BS in Business Administration and Management from California Land University-Northridge.

  

  Appliance Repair Skilful

  Expert Answer

  

  Support wikiHow by unlocking this skilful answer.

  It's usually preferred to exercise this chore with ii people to make it easier. Brand sure you cover the stove and so that it is cushioned just in case the microwave falls during installation. You will need a level drill and drill bit to brand the holes needed so that y'all tin add together the subclass needed to install the microwave. Unless you already have holes present, you will also need to add them to allow ventilation tubes to exist installed.

Inquire a Question

200 characters left

Include your e-mail address to get a message when this question is answered.

Submit

Advertisement

• For loftier cabinet spaces, have an assistant hold the electrical cable out of the way or snake information technology through a hole in the cabinet while y'all lift the microwave.

• If in any incertitude, refer to the manufacturer'due south instruction manual or call the retail shop you purchased the microwave from for more aid.

• Proper ventilation is particularly important for microwaves installed in an RV or other vehicle. Consider using a front-venting microwave or a kit for venting the cabinet to the exterior.

Advertisement

• Do not utilise a microwave manufactured in a region with a dissimilar electrical standard than your present location. This risks permanently destroying your microwave and starting a fire.

• Placing a microwave's vents against the cabinet walls or declining to clean them regularly increases the hazard of fire from dust buildup.

Advertisement

Things Y'all'll Need

• Microwave

For Nether Cabinet Microwaves:

• Microwave'southward Mounting Plate
• Drill
• Stud Finder or Hammer
• Pen or Marker
• Level
• Tape (if y'all accept the newspaper template)
• 3/xvi" (5mm) Lag screws (1-4)
• three/8" (10mm) Toggle screws (2-4)

About This Article

Article Summary X

To install an under chiffonier microwave, first notice your wall studs by borer with a hammer on the wall until you lot hear a solid "thud" rather than a hollow sound. Next, position the mounting plate then information technology'due south level with the lesser of the cabinet and drill holes over the studs and a pigsty for the power string. When you're ready to ready the plate to the wall, get someone to hold the plate while you attach it with lag screws. In one case the plate is in place, thread the ability string through the hole and hang the microwave on the support tabs. For tips on how to install a countertop microwave, read on!

Did this summary aid you?

Thanks to all authors for creating a page that has been read 157,454 times.

Did this article help you?

Source: https://www.wikihow.com/Install-a-Microwave

Posted by: porterallic1989.blogspot.com

Share this post